Ping pong rubbers, like other racquet sports equipment, have a lifespan, which can be extremely short or very lengthy depending on which rubbers you choose. A dead rubber cannot be saved.
However, there are simple actions you can do to help extend the life of your valuable rubbers. I’ll address all of your queries on how to make your ping pong paddle rubber sticky in this article. By the end of the page, you should have a good understanding of how to care for your rubbers.
Difference Between the Grip and Tack
Before we get started, it’s important to grasp the difference between a rubber’s grip and its tackiness. The capacity of the rubber to create spin is referred to as grip. This is the ability of the rubber to retain contact with a single spot on the ball without sliding.
Ping pong rubber tackiness, on the other hand, is more precise. It refers to the rubber’s ability to physically adhere to the ball. A tackiness test may be simply performed by pushing your bat against a ball and holding it upside down to see how long the rubber can hold it without it dropping.
Consider the tackiness of a ping pong rubber to be a type of grip. There are alternative methods to have a sticky rubber without the tackiness. For example, a soft sponge causes the ball to sink deeper into the sponge, increasing the surface area of rubber in contact with the ball.
Ultimately, we’re interested in spin output, and any contribution to grip will suffice. If your rubbers aren’t tacky, don’t worry. They were most likely not intended to be. The great majority of rubbers are only mildly sticky while being quite spinny.
Why Is A Good Grip/Tack Essential?
Ping pong is a sport that relies heavily on the spin. The shots we see at the highest level are only feasible with rubbers that have a high spin capacity.
Poor equipment is frequently blamed for poor athletic performance. It’s almost hilarious. It’s a lame explanation for why you didn’t perform as well as you should have. However, in ping pong, your paddle is quite important. The quality of the paddle has a substantial link with performance for high-level players. A lack of grip restricts your alternatives and compels you to play in a more one-dimensional manner. You can very much say goodbye to looping. Consider an MMA fighter who enters the cage unable to throw any kicks. They’d fare much worse, wouldn’t they?
Top Ways To Keep Your Ping Pong Rubber Sticky
Replace Your Rubbers
The first step in ensuring that your ping pong rubber is grippy or sticky is to evaluate them. What are their ages? Are the edges of the rubbers eroded? Is it possible that the pimples are visible through the rubbers? These might be indicators that it’s time to make a change.
Pinch your rubbers and try pressing from left to right to observe how much resistance the rubbers provide. You may also throw the ball against your bat to get it up in the air and produce a sidespin. Adjust your angle to counteract the spin and ensure that the ball flies straight up in the air when it hits your bat. The greater the angle at which your paddle can be held, the more grip it possesses.
If your rubbers aren’t proving to be particularly grippy, it’s time to replace them. It may be tempting to attempt to save money by purchasing inexpensive rubbers, but I would advocate investing a little more to obtain a nice set.
Clean Your Rubbers
Now that you’ve acquired appropriate grip rubbers, it’s time to extend that hold for as long as feasible. The first step is to clean your ping pong paddle rubbers.
Rubbers are notorious for attracting dirt and dust. This is especially noticeable if you have sticky rubbers. Ping pong balls usually wind up on the floor, where they accumulate whatever muck is present. The floors are filthy, and all of this dirt makes its way to your paddle. It is therefore critical to clean dirt from your rubbers on a regular basis in order to keep them in good condition.
How to Clean Ping Pong Rubbers
Cleaning ping pong rubbers is a straightforward process. First, get a rubber cleaner. These are cleaners specifically developed for table tennis bats. Other cleansers should be avoided since some of them might harm or even corrode your rubbers.
After each session, spray a few drops of solution on both sides of your rubber and wipe it around with a sponge, wiping the dirt outwards. It literally just takes ten seconds, so there is no reason not to do it.
You may also just wash your rubber with water. This is something that a lot of players with sticky rubbers do.
How to Make Ping Pong Paddle Rubbers Sticky
The last way for keeping your ping pong rubber sticky or grippy is to artificially enhance them. This effectively helps to revitalise dying rubbers, giving them new vitality.
You should be aware, however, that whatever you add to your rubbers to improve their grip will only be a temporary solution. The consequences might last weeks or minutes. If you have genuinely dead rubbers, I wouldn’t waste your time attempting to preserve them. Simply get a new pair.
The best way to rejuvenate aged rubbers is to use a booster. The booster should be applied to the sponge rather than the top layer. The sponge expands when a booster is applied. This, in turn, improves the grip of the top sheet when bonded to the blade. The impact lasts 8-12 weeks, which is the longest of any rubber rejuvenation technique. When the booster starts to wear off, simply reapply it.
As previously said, maintaining grip or tackiness is critical if you wish to play at a high level. Many individuals want to know how to make their ping pong paddle sticky, but they should be more concerned with keeping their current grip.
Any artificial grip you are able to create will be transitory and will most likely violate ITTF guidelines.
Instead, simply buy good-quality, long-lasting ping pong rubbers, clean them after each practice, and store them properly. That’s all there is to it.